Test and results » History » Version 4

Version 3 (SANCHEZ, Eduardo, 03/26/2017 10:33 AM) → Version 4/19 (SANCHEZ, Eduardo, 03/26/2017 11:18 AM)

h1. Performance analysis and results

Several tests are carried out in order to evaluate the performance of the developed channel emulator. Firstly, it must be verified that the required Eb/No level is achieved at the demodulator output. Secondly, the time delay of transmitted packets must be measured to guarantee compliance with the specified delay.

h2. Noise measurements

Consider the test bench shown in Figure 1 in In order to measure Eb/No level during in the transmission. The hub modem sends transmission, a QPSK modulated signal to the station modem through the satellite channel represented by the VST. Then, the channel-applied signal is received at the demodulator input of the station modem where the Eb/No measurement is performed. The carrier-to-noise power can be obtained in two different ways by using the monitoring tools of the modem or the spectrum analyzer.

p=. !{width:50%}Noise_test_bench.png!
*Figure 1. Test bench used to measure Eb/No*

A
first approach consist of using the monitoring tools included in of the modem configuration interface. Figure 2 1 shows the measured carrier-to-noise power over 2 minutes for 0 dB, 5 dB, 10 dB, 15 dB, 20 dB and 50 dB. As can be observed the obtained values are approximately the same as the selected Eb/No values in the front panel of the emulator. Nevertheless, as can be seen in Figures 2(e) and 2(f), the obtained carrier-to-noise value is around 16.5 dB while the required Eb/No values are 20 dB and 50 dB. Therefore, it means that there is a upper bound in the Eb/No that can be generated by the channel emulator. Since the modems are connected through an active device, the noise power level is increased according

p=. !{width:50%}Noise_test_bench.png!
*Figure 1. Test bench used
to the VST noise figure and, therefore, the carrier-to-noise power is degraded.

measure Eb/No*

p=. !{width:50%}Modem_carrier_to_noise_ratio.png!
*Figure 2. Eb/No measurements obtained from the modem interface. Selected Eb/No value:(a) 0 dB;(b) 5 dB;(c) 10 dB;(d) 15 dB;(e) 20 dB and (f) 50 dB* interface*

p=. !{width:50%}Ip_throughput_for_5dBand0dB.png!
*Figure 3. IP throughput for 5 dB and 0 dB*

p=. !{width:50%}Degradation_introduced_by_the_emulator.png!
*Figure 4. Eb/No degradation introduced by the emulator*

p=. !{width:50%}Load_effect.png!
*Figure 5. Output power degradation introduced by the emulator*

p=. !{width:50%}Input_demodulator_spectrum.png!
*Figure 6. Signal-to-noise power measurements carried out with the spectrum analyzer*

p=. !{width:50%}Degradation_in_the_output_level.png!
*Figure 7. Signal power degradation due to the emulator*

h2. Delay measurements

p=. !{width:50%}Delay_test_bench_2.png!
*Figure 8. Test bench used to measure a reference round trip time*

p=. !{width:50%}Delay_test_bench.png!
*Figure 9. Test bench used to measure the total round trip time*

p=. !{width:50%} Total_delay_without_emulator.png!
*Figure 10. Round trip time measurements using the ping command (10 packets of 1B and 1500B, respectively) when the emulator is not connected*

p=. !{width:50%}Delay050100150200_1bytes.png!
*Figure 11. Round trip time measurements using the ping command (10 packets of 1B) when the emulator is connected for different delays values*

p=. !{width:50%}Delay050100150200_1500bytes.png!
*Figure 12. Round trip time measurements using the ping command (10 packets of 1500B) when the emulator is connected for different delays values*